Computerised Brother FS101 Computerized Sewing Machine: Setup and First Projects
Learn how to set up and use the computerised Brother FS101 computerized sewing machine, from threading and bobbin winding to choosing stitches for your first pr
Updated November 2026
A computerised Brother FS101 computerized sewing machine is a good fit for beginners and intermediate sewers who want stitch selection at their fingertips without a complicated interface. This guide walks you through unboxing, threading, bobbin work and stitch selection so you can sew a straight seam and a buttonhole with confidence on your first day. It also covers the common mistakes that cause skipped stitches and puckered fabric.
Set Up the Machine Before You Sew
Place the machine on a flat, stable table with room on the left for fabric to hang freely. Plug in the foot control, power cord and any included extension table before switching on. Raise the presser foot and check that the needle is inserted correctly, with the flat side facing back and the needle fully seated in the clamp.
Shopping for one? See our guide: 6 Best Computerized Sewing Machine Brother Models for Every Need (2026).
Before the first project, sew a few inches on scrap fabric using the same thread and needle you plan to use. This tells you whether tension and stitch length are working before you commit to a real garment.
Thread the Upper Thread and Bobbin
Threading order matters more than most beginners expect. Follow the numbered path printed on the machine, guiding the thread through the spool pin, thread guides, take-up lever and needle bar. Missing the take-up lever is the single most common reason for loops and birdnests under the fabric.
Winding and Inserting the Bobbin
Wind the bobbin using the thread path on the bobbin winder, keeping the thread snug but not stretched. When inserting the bobbin into the bobbin case, pull the thread into the slot and under the tension spring so it sits in the correct groove. The bobbin should turn counterclockwise when you pull the thread.
Choose Stitches and Adjust Settings
Select a utility stitch for seams, such as straight stitch or zigzag, and set stitch length according to the fabric. Stitch lengths around 2.5 mm suit most woven cottons, while lighter fabrics often sew better at slightly shorter lengths. Keep tension at the default setting first, and change it only if you see a clear problem on your test piece.
- Straight stitch: general seams and topstitching
- Zigzag: edge finishing and stretch fabrics
- Buttonhole: follow the numbered sequence and test on scrap first
If you are comparing this model with other machines in the line, the Brother CS6000i Computerized Sewing Machine: Setup, Stitches and Tips guide covers a similar stitch-selection workflow that can help you transfer skills between models.
Sew Your First Practice Project
Start with a simple project, such as a pillowcase or a pair of fabric coasters. Cut two pieces of cotton, pin them right sides together, and sew a 1/4-inch seam allowance using a straight stitch. Press the seam open and check for even stitches and flat results.
- Cut two matching cotton squares, about 8 by 8 inches.
- Pin along one edge, pins perpendicular to the seam line.
- Sew slowly with a steady foot pressure and guide fabric gently.
- Backstitch at the start and end to lock the seam.
- Press the seam flat, then turn and press the finished edge.
Common Mistakes
- Forgetting to raise the presser foot before threading, which prevents tension from engaging.
- Using a dull or bent needle, which causes skipped stitches and fabric snags.
- Pulling or pushing fabric through the feed dogs instead of letting the machine feed it.
- Winding the bobbin unevenly, which leads to tension problems on the seam.
- Skipping test stitches on scrap, so problems appear only on finished work.
Recommended Gear
A good set of sharp needles in universal sizes will cover most cotton and blended fabrics you encounter as a beginner. Keep a few extra spools of basic polyester thread in neutral colors so you can match projects quickly. View on Amazon
A small seam ripper makes correcting mistakes faster and keeps fabric from tearing. View on Amazon
FAQ
Why does my stitch look different on the top and bottom of the fabric?
This usually means the upper or bobbin tension is off. Rethread both threads completely, then sew a test line on scrap and adjust tension only if the problem remains.
How often should I change the needle?
Replace the needle after roughly eight hours of sewing or whenever you hear a clicking sound or notice skipped stitches. Changing it at the start of each major project is a simple habit that prevents many issues.
Can I use this machine for heavy denim?
Denim is possible with a heavy-duty needle and a slightly longer stitch, but sew slowly and avoid forcing thick seams. Consult the manual for the maximum recommended fabric thickness.
Conclusion
With the machine threaded correctly, bobbin seated properly and a practice piece sewn, the computerised Brother FS101 computerized sewing machine becomes straightforward to use. Work through a few simple projects to learn how it responds to different fabrics. Once you are comfortable, you can move on to more demanding techniques.
Related reading
- Computerized Brother Sewing Machine Models: 6 Picks by Skill Level (2026)
- Brother Xr3340 Computerized Sewing and Quilting Machine: A Practical Guide (2026)
- Brother XS2080 Computerized Sewing Machine: Setup, Stitches and Buying Tips
- Brother XR9550 Computerized Sewing and Quilting Machine Details: Specs and Setup
- Brother XR9550 Computerized Sewing Machine Review: Features and Performance
Ready to choose one?
