We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Brother CE1150 Computerized Sewing Machine Needle Threader: Step-by-Step Fix

Learn how to use the brother ce1150 computerized sewing machine needle threader, fix common threading misses, and keep your needle threader working reliably on

Updated November 2026

The brother ce1150 computerized sewing machine needle threader is a small built-in hook that pulls your thread through the needle eye for you. This guide shows you how to use it correctly, how to fix the most common misses, and how to tell whether a threader problem is really a threading problem. Most issues come down to a few simple checks.

Before You Start: Prepare the Machine

Raise the presser foot before threading, and turn the handwheel toward you until the needle is at its highest point. A needle that sits low can make the threader hook sit at the wrong angle and miss the eye. Confirm the needle is inserted fully into the clamp, flat side facing the back, and that it is not bent or burred. A damaged needle is one of the most common reasons the threader seems to fail.

How to Use the Needle Threader Step by Step

  1. Thread the machine completely through the thread guides, the tension discs, and the take-up lever, following the threading diagram printed on the machine.
  2. Pull the needle threader lever down slowly until the hook rests fully in front of the needle eye.
  3. Bring the thread end from the front of the needle across the hook, keeping a little slack so the thread sits in the hook’s notch.
  4. Release the lever gently. The hook passes through the eye and draws a loop of thread to the back of the needle.
  5. Pull the loop out to the front, leaving a tail of about 4 to 6 inches (roughly 10 to 15 cm) for hand-tying or for drawing under the presser foot.

Sub-step: Check the Hook Position

The hook should pass through the center of the eye, not against one side. If it hits the eye edge every time, the needle is likely a few degrees out of position. Loosen the needle clamp screw slightly, reseat the needle fully, and tighten again before retrying.

Fixing Common Threader Problems

When the threader repeatedly fails, work through these checks before assuming the mechanism is broken. The table below matches symptoms to likely causes.

Symptom Likely cause What to do
Hook misses the eye Needle not fully seated or set at an angle Reinsert the needle, flat side back, and push it all the way up
Thread slips off the hook Thread not seated in the hook notch Lay the thread across the hook and gently draw it into the notch before releasing
Loop is too short Not enough slack at the front of the needle Pull out a little more thread from the spool before threading
Hook bends or jams Forcing the lever or a bent needle Stop, remove the needle, check for damage, and replace if bent

Choosing the Right Needle and Thread for Best Results

The threader works best with a needle and thread that are sized to match. Thread that is too thick for the needle eye will not slide through the hook, and a very fine thread can slip off the hook entirely. Stick to standard needles recommended for your fabric, and replace any needle that has been used on heavy denim or quilting for many projects. Check the Brother CE1150 Computerized Sewing Machine Review: Is It Worth It? guide for notes on which needle types this model accepts.

Common Mistakes and Tips

  • Threading the machine with the presser foot down, which can affect tension and loop formation.
  • Using the threader with the needle raised only partway, so the hook cannot reach the eye squarely.
  • Pulling the thread hard before the hook has released it, which can break fine thread.
  • Skipping the upper threading path. The threader cannot compensate for thread missing a guide.
  • Ignoring a bent needle. Replace it rather than trying to straighten it.

A few supplies make threading and needle changes easier:

  • Brother replacement needles in a standard assortment help you match needle size to fabric and keep a fresh needle on hand when the threader starts missing. View on Amazon
  • A small pair of snips lets you trim thread tails cleanly after threading without fraying the end. View on Amazon
  • A seam ripper with a fine tip is useful for removing stitches when a threading error shows up mid-project. View on Amazon

FAQ

Why won’t the needle threader catch my thread?

The most common reason is that the needle is not fully inserted or is set at a slight angle. Reinsert the needle with the flat side facing back, push it firmly up, and try again.

Can I use the needle threader with any needle?

Use standard needles sized for your fabric and thread. Very fine or very thick needles may not pass cleanly through the hook, so check the machine’s manual for the recommended range.

Should I still thread by hand if the threader fails?

Yes. Manual threading is a reliable fallback, and it lets you confirm the thread path is correct. If the threader keeps failing after you have checked the needle, consult an authorized Brother service center.

Conclusion

The brother ce1150 computerized sewing machine needle threader works best when the needle is fresh, fully seated, and the presser foot is raised before you start. Follow the step-by-step method, use the troubleshooting table when something goes wrong, and keep a spare needle nearby. With those habits, threading becomes a quick step rather than a frustration.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our sewing supplies guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Sewing Thread Online.