We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Thread a Brother Computerized Sewing Machine: A Step-by-Step Guide

Learn how to thread a Brother computerized sewing machine step by step, from the spool pin to the needle eye, plus fixes for the most common threading mistakes.

Updated November 2026

To thread a Brother computerized sewing machine, you raise the needle, guide the upper thread through the numbered path on the machine, and pull it through the needle eye from front to back. Most Brother models use a color-coded or numbered diagram printed on the machine, so the process is the same across many models. This guide walks through each step and explains what to check when the thread keeps breaking or skipping.

Before You Start

Set up the machine so the thread can flow without snagging. Turn the machine off, make sure the presser foot is raised, and place a spool of thread on the spool pin. Use the spool cap that matches the spool size. A spool that is too large for the cap can wobble and cause uneven tension.

Shopping for one? See our guide: 6 Best Computerized Sewing Machine Brother Models for Every Need (2026).

  • A spool of thread in the weight suited to your fabric
  • A fresh needle in the correct size for your project
  • The machine’s instruction manual or the threading diagram on the machine body
  • A pair of sewing scissors to trim the thread tail

Thread the Upper Thread Step by Step

  1. Raise the needle. Turn the handwheel toward you until the needle bar reaches its highest position. Threading with the needle down can pull the thread out of the tension discs.
  2. Place the spool. Set the spool on the spool pin so the thread unwinds counterclockwise, or as your model’s diagram shows. Add the spool cap or felt pad.
  3. Follow the numbered path. Bring the thread down through the thread guides in the order marked on the machine, usually numbered 1 through 4 or indicated by arrows. Hold the thread taut as you guide it.
  4. Pass through the tension discs. Bring the thread down between the tension discs at the front of the machine. Make sure it sits between the discs, not on the outside.
  5. Pull the thread up to the take-up lever. Guide the thread into the take-up lever, then down the front to the needle area. The take-up lever must have thread running through its eye.
  6. Thread the needle. Use the automatic needle threader if your model has one. Lower the presser foot first, since the threader works best with it down. Pull the lever or button, catch the loop, and pull the thread through the eye to the back.
  7. Pull out a tail. Pull about 4 to 6 inches of thread through the needle eye and lay it to the back of the presser foot. Trim the tail if it is too long.

Wind and Thread the Bobbin

The bobbin thread is separate from the upper thread. Wind the bobbin by placing an empty bobbin on the bobbin winder spindle, guiding thread through the winder tension, and pressing the winder into position. Stop the winder once the bobbin is full, which many Brother manuals describe as a slightly domed or filled bobbin. Insert the bobbin into the bobbin case so the thread unwinds in the direction shown in your manual, then pull the thread through the slot to engage the tension spring.

Once the bobbin is in place, bring up the bobbin thread by holding the upper thread lightly and turning the handwheel one full rotation. A loop of bobbin thread should appear. Pull both threads toward the back of the machine before you begin stitching.

Common Mistakes and Quick Fixes

  • Thread not in the tension discs. If the stitches look loose or the thread breaks, retrace the path and confirm the thread sits between the discs.
  • Needle threaded from the wrong side. The thread should pass from front to back through the eye. Reverse threading causes skipped stitches.
  • Needle inserted incorrectly. Push the needle fully up into the clamp with the flat side facing the back, as your manual specifies.
  • Forgetting to raise the presser foot. Threading with the foot down can prevent the thread from seating properly in the tension system.

If stitches still skip after you thread correctly, check the needle for damage and replace it. For tension problems, see our guide to Computerized Sewing Machine Automatic Tension: How It Works and How to Adjust It.

A clean, sharp pair of thread snips makes it easier to trim tails and keeps threads from fraying at the needle eye. Find them here: View on Amazon.

A spool cap set helps prevent spools from wobbling on the spool pin, which can cause uneven tension. Browse options here: View on Amazon.

FAQ

Do I need to thread the bobbin before the upper thread?

No. Most people wind and insert the bobbin first, then thread the upper thread, and finally bring up the bobbin thread. The order does not affect the machine as long as each step is done correctly.

Why does my Brother machine keep breaking the thread?

The most common causes are an incorrectly threaded tension path, a damaged needle, or a thread that is too heavy for the needle. Re-thread the machine with the presser foot up, and replace the needle if it is bent or dull.

Can I use the automatic needle threader every time?

Yes, if your model has one. Use it with the presser foot lowered, and check that the thread lies in the needle eye. If the threader fails repeatedly, thread the needle by hand.

Conclusion

Threading a Brother computerized sewing machine becomes routine once you know the path: spool, thread guides, tension discs, take-up lever, then needle. Keep the presser foot up, follow the numbered diagram, and check that the thread sits in the tension discs before you stitch. If problems continue, consult your machine’s manual or an authorized service technician.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our sewing supplies guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Sewing Thread Online.