Singer Perfect Finish Computerized Sewing Machine ET1: Setup and Use Guide
Learn how to set up, thread, and use the Singer Perfect Finish Computerized Sewing Machine ET1, with stitch selection, tension tips, and fabric matching advice.
Updated November 2026
The Singer Perfect Finish Computerized Sewing Machine ET1 is a straightforward machine for everyday sewing, and this guide walks you through threading it, choosing stitches, and matching needles and tension to your fabric. By the end, you should be able to get a clean first seam and know where to look when something goes wrong. Treat these steps as a general outline and check your machine’s manual for model-specific diagrams and settings.
Set Up the Machine Before the First Stitch
Place the machine on a flat, stable surface with the power switch off and the foot control unplugged. Raise the presser foot before threading, because the tension discs only open and close properly when the foot is up. Install a fresh needle, flat side facing back, and push it all the way up into the clamp before tightening the screw.
Shopping for one? See our guide: 7 Best Computerized Sewing Machine Singer Models for 2026.
Thread the Upper Thread and Bobbin
Most computerized Singer models use a numbered threading path printed on the body or in the manual. Follow it in order, guiding the thread through the spool pin, thread guides, take-up lever, and needle bar. For the bobbin, wind thread evenly by hand or with the bobbin winder, drop the bobbin into its case with the thread feeding in the correct direction, and pull the thread through the slot to engage the tension spring.
Choose Stitches and Adjust Tension for Your Fabric
Use the stitch selector to pick the pattern you need, then match the stitch length and width to the job. Thin, woven fabrics like cotton lawn usually sew best with a shorter stitch length, while knits need a stretch stitch so seams do not pop. Sew a test piece using scrap from the same fabric before starting the project.
| Fabric type | Suggested needle | Stitch choice |
|---|---|---|
| Quilting cotton | Size 80/12 universal | Straight stitch, 2.5 mm length |
| Jersey knit | Size 75/11 ballpoint | Stretch or zigzag stitch |
| Denim | Size 90/14 denim | Straight stitch, 3 mm length |
Checklist before you sew
- Presser foot raised during threading
- Needle size matches the fabric weight
- Upper thread and bobbin thread both seated in their guides
- Test stitch sewn on scrap fabric
- Tension checked on both sides of the seam
Common mistakes
- Threading with the presser foot down, which keeps tension discs closed and causes loops.
- Using a dull or bent needle, which skips stitches and can damage fabric.
- Winding the bobbin unevenly, which leads to inconsistent tension.
- Skipping the test seam and discovering tension problems halfway through a project.
Recommended gear
A supply of universal and ballpoint needles in several sizes covers most fabrics you will sew on this machine. A small bobbin case cleaning brush keeps lint from affecting tension over time. A seam ripper helps you correct stitches without damaging the fabric around them.
- Universal and ballpoint sewing machine needle assortment: useful because the right needle type for each fabric prevents most skipped stitches. View on Amazon
- Sewing machine lint brush kit: helps keep the bobbin area clean so tension stays consistent. View on Amazon
- Seam ripper with ergonomic handle: makes removing stitches faster and safer for delicate fabric. View on Amazon
FAQ
Why does my stitch look loose on one side?
Uneven tension usually comes from threading errors, an incorrectly seated bobbin, or a mismatch between thread weight and needle size. Rethread the upper thread with the presser foot up and recheck the bobbin direction.
How often should I change the needle?
Many sewists replace the needle after roughly eight hours of sewing or whenever you notice skipped stitches or fraying thread. Manufacturers generally recommend changing it regularly for best results.
Can I sew stretch fabric on this machine?
Yes, using a ballpoint or stretch needle and a stretch stitch lets seams flex with the fabric. Test on scrap first, since the ideal settings depend on the knit’s weight and stretch.
Conclusion
Setting up the Singer Perfect Finish Computerized Sewing Machine ET1 correctly, matching the needle and stitch to your fabric, and testing before you sew will prevent most frustrations. Keep the bobbin area clean and replace needles regularly. For model-specific details, always consult the official Singer manual.
Related reading: Singer Superb Computerized Sewing Machine: A Practical Guide (2026) and Singer One Easy to Use Computerized Sewing Machine: A Beginner's Guide (2026) cover similar setup steps on other Singer models.
Related reading
- Supreme Singer Sp68 Computerized Sewing Machine: A Practical Guide (2026)
- Singer Stylist 7258 Computerized Sewing Machine: A Practical Guide (2026)
- Singer Special Edition Computerized Sewing Machine: A Practical Guide (2026)
Ready to choose one?
