Brother Innov-is A150 Computerized Sewing Machine: Setup Guide for Beginners
Learn how to set up, thread and use the Brother Innov-is A150 computerized sewing machine, with beginner tips, common mistakes and a quick FAQ for new owners.
Updated November 2026
This guide walks you through setting up the brother innov-is a150 computerized sewing machine, threading it correctly, choosing stitches and avoiding the errors new owners run into most. By the end, you should be able to sew your first straight seam and a basic zigzag with confidence. Most problems on this model trace back to threading and bobbin setup, so those steps get the most attention below.
Unboxing and Placing the Machine
Set the machine on a flat, stable table with clear space on the left for fabric and on the right for the thread spool. Plug in the foot control and connect the power cord before you turn the machine on. Remove the accessory tray and check that you have the bobbins, presser feet, seam ripper and needle set included with your kit. Keep the manual nearby, since the stitch chart and tension guidance are easier to follow with it open.
Shopping for one? See our guide: 7 Best Brother Duetta 2 Innov-is 4750d Computerized Sewing Embroidery Machines (2026): Our Picks.
Threading the Upper Thread and Bobbin
Threading is where most beginners go wrong, so follow the marked guides on the machine in order. Raise the needle to its highest position, place the spool on the spool pin, and guide the thread through each numbered slot until it reaches the needle. Thread the needle from front to back, and pull out a few inches of tail before you start sewing.
- Raise the presser foot so the tension discs open.
- Wind a bobbin using the bobbin winder and seat it in the bobbin case.
- Pull the bobbin thread up through the throat plate slot and hold the tail.
- Lower the presser foot and turn the handwheel toward you once to bring up the bobbin thread.
- Check that both threads lie under the presser foot before stitching.
Choosing Stitches and Setting Tension
The computerized stitch selector lets you pick a stitch pattern, then adjust width and length on the screen or dial. Start with a plain straight stitch at a medium length, around 2.5 mm, and test it on scrap fabric before every project. Tension problems usually show up as loops on the top or bottom of the seam, and small changes in the tension dial usually correct them. Match your needle to the fabric weight and change it when it starts skipping stitches.
Practicing Your First Seams
Use two layers of cotton or a similar medium-weight fabric to practice straight seams. Set a seam allowance of 1/4 inch by aligning the fabric edge with the guide on the throat plate. Sew slowly, guide the fabric gently rather than pulling it, and backstitch at the start and end to lock the seam. Once your seams are even, move on to zigzag and decorative stitches on scrap pieces before using them on a real project.
Common Mistakes
- Skipping the step of raising the presser foot before threading, which leaves the tension discs closed.
- Sewing with a dull or bent needle, which causes skipped stitches and puckering.
- Forgetting to re-thread the machine completely after changing spools or colors.
- Pulling fabric through the feed, which bends the needle and misaligns seams.
- Ignoring the bobbin case orientation, so the bobbin thread runs the wrong direction.
Recommended Gear
- Universal sewing machine needles: Keeping a fresh needle set on hand prevents skipped stitches and fabric damage. View on Amazon
- Pre-wound bobbins for your machine class: Having spares ready saves time when you switch thread colors mid-project. View on Amazon
- Seam ripper with a fine tip: A good seam ripper makes correcting mistakes faster and protects the fabric. View on Amazon
For more on this machine’s features, see Brother XR7700 Computerized Sewing Machine: Setup, Stitches and Tips and How to Thread a Brother Computerized Sewing Machine: A Step-by-Step Guide. If you are comparing models, Computerized Brother Sewing Machine Models: 6 Picks by Skill Level (2026) covers the range by experience level.
FAQ
Is the brother innov-is a150 computerized sewing machine good for beginners?
Yes, it suits beginners who want built-in stitch selection and guided settings. Practice on scrap fabric first to learn how the tension and stitch controls respond.
Why does my stitch skip on the brother innov is a150 computerized sewing machine?
Skipped stitches usually come from a dull or incorrectly inserted needle, or from threading that did not seat the thread in the tension discs. Replace the needle and re-thread with the presser foot raised.
How often should I clean the bobbin area?
Clean lint from the bobbin area whenever you change bobbins, using the brush included with the machine. Regular cleaning helps keep stitches even and reduces tension issues.
Conclusion
With careful threading, a fresh needle and a few practice seams, the brother innov-is a150 computerized sewing machine becomes easy to control. Work through the basic stitches on scrap fabric before starting real projects. Consult your manual or a sewing machine technician if problems persist after troubleshooting.
Related reading
- How to Use a Brother Computerized Sewing Machine CS6000i: A Step-by-Step Guide
- How to Use Brother Computerized Sewing Machine: A Practical Guide (2026)
Ready to choose one?
