Brother XR1355 Computerized Sewing Machine: A Setup and Stitching Guide
Learn how to set up, thread and stitch with the Brother XR1355 computerized sewing machine, plus tips for common problems and fabric-matched settings.
Updated November 2026
The Brother XR1355 computerized sewing machine is a good fit for beginners and intermediate sewists who want built-in stitch selection and automatic features without a complicated interface. This guide walks you through unboxing and setup, threading, choosing stitches and settings for common fabrics, and avoiding the mistakes that cause most early frustration. Work through the steps in order the first time you sit down at the machine.
Set Up the Machine Before You Sew
Place the machine on a flat, stable surface with enough room on the left for fabric to hang freely. Plug the foot control into the back of the machine, then connect the power cord and switch the machine on. Raise the presser foot and confirm the machine is on a stable base before you start.
Shopping for one? See our guide: 6 Best Computerized Sewing Machine Brother Models for Every Need (2026).
- Remove the accessory box and check for the presser feet, bobbins, seam ripper and needles.
- Insert a fresh needle with the flat side facing back, pushing it up until it stops.
- Wind a bobbin using the bobbin winder and seat it in the bobbin case in the direction the manual shows.
Thread the Upper and Lower Threads Correctly
Most threading problems come from skipped guides. Raise the needle to its highest position, place the spool on the spool pin, and follow the numbered threading path on the machine, including the thread guide near the needle. Pull the thread through the needle eye from front to back, leaving a tail of about 4 to 6 inches.
For the bobbin, pull the thread through the slot in the bobbin case, then under the tension spring. Hold the thread and bring the upper thread up with a gentle pull so both threads lie together under the presser foot before you start sewing.
Choose Stitches and Settings for Your Fabric
Match your needle, thread and stitch length to the fabric before you stitch. Lightweight woven cottons and quilting cotton do well with a size 80/12 needle and a standard straight stitch at about 2.5 mm. Denim and canvas call for a size 90/14 or 100/16 needle and a slightly longer stitch. Knits need a ballpoint or stretch needle, and a narrow zigzag or stretch stitch so seams do not pop.
Test every new combination on a scrap of the same fabric, layered the same way as your project. Check the top and bottom of the seam for even tension. If the bobbin thread shows on top, the upper tension is probably too tight; if loops form underneath, it is usually too loose. For more on stitch selection, see Brother XR7700 Computerized Sewing Machine: Setup, Stitches and Tips.
Sew Your First Seam Step by Step
- Lower the presser foot onto your fabric, with the seam allowance aligned with the guide on the throat plate.
- Hold both thread tails lightly behind the foot and take two or three stitches to lock the seam.
- Sew at a steady, moderate speed and guide the fabric gently. Do not pull or push it.
- Stop with the needle down, raise the presser foot, and clip the threads leaving tails of about 3 inches.
If you are planning larger projects such as quilts, the layout and stitch options differ from a standard model. Brother XR9550 Computerized Sewing and Quilting Machine Details: Specs and Setup covers those differences in more detail.
Common Mistakes and Tips
- Installing the needle backward. The flat side must face the back of the machine, or skipped stitches will follow.
- Forgetting to re-thread the upper thread after rewinding the bobbin, which causes tension problems.
- Sewing with a dull or bent needle. Replace it after a few projects or any time you hear a clicking sound.
- Pulling fabric through the feed dogs. Let the machine feed the fabric and only steer it.
- Cleaning lint from the bobbin area after every project. Lint buildup is a common cause of erratic stitches.
Recommended Gear
- A pack of universal sewing machine needles in a range of sizes lets you match the needle to each fabric type. View on Amazon
- Pre-wound bobbins that fit your machine’s bobbin case help you keep tension consistent between projects. View on Amazon
- A small seam ripper and a pair of thread snips make correcting mistakes and trimming tails quicker. View on Amazon
FAQ
What needle should I use with the Brother XR1355?
Start with a universal size 80/12 for woven cottons and a size 90/14 for denim or heavier fabrics. Use a ballpoint or stretch needle for knits.
Why are my stitches skipping?
The most common causes are a bent or dull needle, incorrect needle installation, or a needle that is not suited to the fabric. Replace the needle first and check the threading path.
How often should I clean the machine?
Remove lint from the bobbin area and feed dogs after each project, and follow the cleaning schedule in your manual for a more thorough service.
Conclusion
With the machine set up correctly, threaded along the proper path, and matched to your fabric, the Brother XR1355 handles everyday sewing with reliable results. Test your settings on scrap fabric before every project. Keep your needles fresh and your bobbin area clean, and most issues will be easy to solve.
Related reading
- Computerized Brother Sewing Machine Models: 6 Picks by Skill Level (2026)
- Brother Xr3340 Computerized Sewing and Quilting Machine: A Practical Guide (2026)
- Brother XS2080 Computerized Sewing Machine: Setup, Stitches and Buying Tips
Ready to choose one?
