How to Use Brother CS5055 Computerized Sewing Machine: A Step-by-Step Guide
Learn how to use Brother CS5055 computerized sewing machine, from threading and bobbin setup to choosing stitches and sewing your first seam cleanly.
Updated November 2026
To use a Brother CS5055 computerized sewing machine, you need to wind and insert the bobbin, thread the upper path, select a stitch on the LCD, and set the tension and foot before you sew. Once those basics are in place, you can sew straight seams, zigzags and buttonholes with consistent results. This guide walks through each step in the order you will actually need them.
Prepare the Machine Before You Sew
Start by raising the presser foot and turning the machine off. Attach the correct foot for your task, usually the all-purpose foot for general sewing, and make sure the foot snaps down securely. Place a spool of thread on the spool pin, add the spool cap, and set the bobbin winding guide so the thread feeds smoothly.
- Wind the bobbin by guiding the thread through the bobbin winder tension guide, then press the winder arm toward the bobbin until it engages.
- Start the machine briefly to fill the bobbin. Stop when it is full, cut the thread, and release the winder.
- Drop the bobbin into the bobbin case with the thread feeding in the direction the diagram on the case indicates.
- Pull the thread through the slot in the case and check that it sits under the tension spring.
Thread the Upper Path and Select a Stitch
Raise the needle to its highest position using the needle up/down button or the handwheel, then follow the numbered threading path printed on the machine. Pass the thread through the upper guides, the take-up lever, and finally through the needle from front to back. Leave a 4 to 6 inch tail to hold while you sew the first few stitches.
Use the LCD screen to choose a stitch. Stitch numbers and names appear on the display, and the recommended presser foot usually shows as well. Match the foot to the stitch before you start, because the wrong foot can cause jamming or uneven feed.
Set Tension, Length and Width
Most computerized machines handle tension automatically, but you can still adjust it when a seam looks wrong. Test on a scrap of the same fabric, folded in layers if you plan to sew a double thickness. Adjust stitch length for the fabric weight: shorter lengths suit lightweight fabric, and longer lengths suit basting or heavy denim. Use width settings for zigzag stitches to keep edges clean.
| Fabric type | Suggested stitch length | Thread note |
|---|---|---|
| Lightweight cotton or voile | Short (about 2 mm) | Fine thread to avoid puckering |
| Medium cotton or cotton blends | Standard (about 2.5 to 3 mm) | All-purpose polyester thread |
| Denim or canvas | Slightly longer (about 3 to 4 mm) | Heavier thread and a size 90/14 needle |
For a clear overview of how automatic tension behaves on computerized models, see Computerized Sewing Machine Automatic Tension: How It Works and How to Adjust It.
Sew Your First Seam
Place the fabric under the presser foot with the seam allowance aligned to the guide on the throat plate. Lower the presser foot, hold both thread tails for the first stitch, and press the start/stop button or foot control gently. Guide the fabric with both hands, but do not pull or push it, because the feed dogs control the movement. Stop with the needle down, lift the foot, and pivot when you need to turn a corner.
If you are unsure which settings suit a particular project, a general overview of the model may help. The Brother CS5055 Computerized Sewing Machine Review: Is It Worth It? article covers its typical strengths and limitations, and What Is a Computerized Sewing Machine? Definition and How It Works explains the underlying features.
Common Mistakes and Tips
- Forgetting to raise the presser foot before threading can cause tension problems and skipped stitches.
- Using a bent or dull needle leads to skipped stitches and thread breaks. Replace the needle after a project or when you hear a dull thumping.
- Sewing a stitch that does not match the presser foot can jam the machine. Check the foot number on the LCD first.
- Always test settings on scrap fabric in the same weight and layers before starting the real piece.
- Clean lint from the bobbin area every few projects, using the brush supplied with the machine.
Recommended Gear
- Brother universal sewing machine needles: Matching needle size to fabric reduces skipped stitches and thread breaks. View on Amazon
- Brother all-purpose presser foot set: Feet made for this model help the stitch feed evenly and make the right stitch width possible. View on Amazon
- Brother bobbins: Pre-wound or spare bobbins let you switch thread colors without rewinding each time. View on Amazon
FAQ
Why does my Brother CS5055 skip stitches?
Skipped stitches usually come from a dull or incorrectly sized needle, or from threading that is not fully seated in the tension discs. Replace the needle with a fresh one that suits your fabric, then rethread the upper path with the presser foot raised.
How do I know which presser foot to use?
The LCD screen typically shows the recommended foot for the stitch you select. Attach the matching foot and confirm it clicks into place before you begin sewing.
Can I sew thick fabric like denim on this machine?
Yes, with a heavier needle, such as a size 90/14, and a slightly longer stitch length. Sew slowly, and avoid pushing the fabric through, since the feed dogs will move it for you.
Conclusion
Once you have wound the bobbin, threaded the upper path, and matched the stitch and foot, the Brother CS5055 is straightforward to run. Test every new fabric on scrap first, and adjust length and tension only when the stitch looks wrong. With those habits, your seams will stay even from the first project onward.
Related reading
- Brother SE-270D Computerized Sewing Machine: A Practical Setup and Use Guide
- 7 Best Brother International Cs5055 Computerized Sewing Machines (2026): Our Picks
Ready to choose one?
