We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Juki HZL-70HW Computerized Sewing Machine: Setup and Key Features Guide

Learn how to set up, thread and use the Juki HZL-70HW computerized sewing machine, plus the features to check before you buy and common beginner mistakes to avo

Updated November 2026

The Juki HZL-70HW computerized sewing machine is a straightforward option for sewers who want built-in stitch selection and automatic features without a complicated control panel. This guide walks you through unboxing, threading, bobbin setup and the features worth checking, so you can start sewing with confidence. If you are still deciding whether this model fits your projects, the answers below will help you decide.

Before You Start: Unboxing and Placement

Set the machine on a flat, sturdy table with room for fabric to move freely on both sides of the needle. Keep the machine away from direct heat sources and dust. Remove the accessory box and check for the foot pedal, power cord, presser feet, bobbins, needles, seam ripper and the instruction manual. Keep the packaging for a while in case you need to transport or service the machine later.

Shopping for one? See our guide: Juki HZL-F600 Computerized Sewing and Quilting Machine Review: Is It Worth It?.

How to Thread and Wind the Bobbin

Bobbin problems cause more beginner frustration than almost anything else, so take your time here. Follow these steps:

  1. Turn the machine off and raise the presser foot.
  2. Place the spool of thread on the spool pin, with the thread unwinding in the direction shown in your manual.
  3. Guide the thread through the bobbin winder guides and wind a few turns around the empty bobbin by hand.
  4. Engage the bobbin winder and press the foot pedal. Stop once the bobbin is full, usually when the wound thread reaches the edge of the bobbin.
  5. Drop the wound bobbin into the bobbin case so the thread unwinds counterclockwise, then pull the thread through the slot and under the tension spring.

Threading the Upper Thread and Setting Tension

Upper threading follows the numbered path printed on the machine body. Thread from the spool pin, through each guide in order, and down through the take-up lever before passing the thread through the needle eye from front to back. Most sewing problems that look like tension trouble are actually threading errors, so check the path again if stitches look loose or the thread keeps breaking.

For regular woven fabrics, the automatic tension setting is a good starting point. Sew a test strip with two layers of the same fabric you plan to use. If the top thread shows loops on the underside, tension is too tight on the top. If the bobbin thread shows on the top, the upper tension is too loose. Adjust in small steps and sew a fresh test each time.

Choosing Stitches, Feet and Needles

Match your needle and presser foot to the fabric before you select a stitch. Lightweight knits need a ballpoint or stretch needle, while denim and canvas need a heavier sharp needle. A standard straight stitch covers most seams, and a zigzag handles finishing edges and light stretch. Check the stitch length and width on the screen before starting a long seam, and sew a sample on scrap fabric first.

Common Mistakes and Tips

  • Re-threading the top path after a single skipped guide, which often causes looping and skipped stitches.
  • Using a dull or bent needle, which produces skipped stitches even when tension is correct.
  • Forgetting to raise the presser foot before re-threading, which can leave the tension discs closed and the thread jammed.
  • Skipping a test seam on each new fabric, which makes tension problems harder to diagnose later.
  • Pulling fabric through the feed dogs, which can bend needles and shift seam alignment.

A few supplies make everyday sewing on this machine easier. Choose a set of sharp and ballpoint needles in common sizes so you can switch quickly between woven and knit fabrics. View on Amazon

Pre-wound bobbins that match your machine’s bobbin type save time and reduce tension issues caused by uneven hand-winding. View on Amazon

A sturdy seam ripper with a fine tip helps you correct mistakes without damaging the fabric. View on Amazon

FAQ

Is the Juki HZL-70HW suitable for beginners?

Many beginners find the built-in stitch selection and automatic tension helpful while learning. Setting aside time for a few test seams on scrap fabric will make the learning curve much smoother.

Why is my stitching looping on the underside of the fabric?

Looping usually means the upper thread is not seated correctly in the tension discs or the thread path has a skipped guide. Re-thread the machine with the presser foot raised and sew a fresh test strip.

Where can I find the official manual and current specifications?

The manual that ships with the machine is the most reliable source for threading diagrams and stitch charts. For current specifications, warranty details and service options, check the official Juki website or contact an authorized dealer.

Conclusion

Once you master threading, bobbin winding and tension testing, the Juki HZL-70HW computerized sewing machine becomes a reliable everyday tool. Keep a practice piece of scrap fabric nearby and sew test strips before each project. If you want to compare models, browse related guides on this site to find the right fit for your sewing goals.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our sewing supplies guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Sewing Thread Online.