Brother Computerized Sewing and Quilting Machine Xr1355: A Practical Guide (2026)
Learn how to set up, thread, and stitch with the brother computerized sewing and quilting machine xr1355, plus fabric, needle, and tension tips for better resul
Updated November 2026
The brother computerized sewing and quilting machine xr1355 is a feature-rich machine that rewards a careful first setup. This guide walks you through unpacking and placing the machine, threading the upper path, winding and inserting a bobbin, choosing a stitch, and testing tension before you start a real project. Follow the steps in order and you should finish with clean, balanced stitches on your first test sample.
Prepare the Machine and Your Workspace
Place the machine on a flat, stable table with at least a few inches of clear space on the left for fabric support. Plug in the foot control and power cord, then switch the machine on and let the display light up before touching any settings. Keep the free arm and bed free of lint, since a small amount of buildup near the bobbin area can cause skipped stitches.
Shopping for one? See our guide: Brother CS7000X Computerized Sewing and Quilting Machine Review (2026).
- Brother XR1355 machine with foot control and power cord
- Included accessory box (presser feet, bobbins, seam ripper, screwdriver)
- Thread in a weight matched to your fabric
- Test fabric scraps of the same weight as your project
- A new universal needle, sized to your fabric
Thread the Upper Thread Path
Raise the needle to its highest position and lift the presser foot before threading. Follow the numbered guides printed on the machine body, passing the thread through the spool pin, thread guides, tension discs, take-up lever, and needle bar guide in sequence. Pull about four inches of thread through the needle eye from front to back, leaving a tail to hold while you start your first stitches. Skipping a guide is the most common reason for loops on the underside of the fabric, so double-check each step.
Wind and Insert the Bobbin
Place a bobbin on the winder spindle, guide the thread through the small bobbin tension slot, and press the winder into position. Let the machine fill the bobbin evenly, then stop it at about 80 to 90 percent full so the thread doesn’t spill or pull unevenly. To insert the bobbin, drop it into the bobbin case so the thread unwinds counterclockwise, then pull the thread into the slot under the tension spring and out the finger.
Choose Stitches and Test Tension
Select a utility stitch such as a straight stitch for your first test, then set stitch length to about 2.5 mm and width to zero. Sew a few inches on a double layer of test fabric and check the top and bottom of the seam. Upper and lower threads should meet in the middle of the fabric layers, with no visible bobbin thread on top or loose loops underneath. If you see bobbin thread on top, tighten the upper tension one step at a time, and if the top thread is looping underneath, loosen it. For a deeper look at threading and stitch selection, see How to Thread a Brother Computerized Sewing Machine: A Step-by-Step Guide and How to Use Brother Computerized Sewing Machine: A Practical Guide (2026).
Match Needle and Thread to Your Fabric
Needle size and thread weight should follow the fabric, not the other way around. Lightweight cottons and voiles usually work with a size 70/10 needle, while quilting cottons and light denim suit size 80/12, and heavy denim or canvas call for size 90/14 or larger. Cotton or polyester thread in a standard weight is a safe default for piecing and quilting. For a quilt-specific model with a similar layout, see Brother XR1355 Computerized Sewing Machine: A Setup and Stitching Guide.
Quick Reference
| Fabric | Needle | Thread |
|---|---|---|
| Voile, chiffon | 70/10 universal or sharp | Fine cotton or polyester |
| Quilting cotton | 80/12 universal or quilting | Cotton or 50-weight polyester |
| Denim, canvas | 90/14 denim or jeans | Heavy-duty polyester |
Common Mistakes
- Sewing with the presser foot down during threading, which can cause the tension discs to misalign.
- Using a bent or dull needle, which often produces skipped stitches.
- Changing several tension settings at once instead of adjusting one step at a time.
- Forgetting to clean lint from the bobbin area after a long quilting session.
- Pulling fabric through the feed dogs instead of guiding it gently.
Recommended Gear
A stable extension table helps when quilting larger pieces, since it keeps the weight of the quilt from pulling the fabric off the bed. View on Amazon
A set of fresh universal and denim needles in mixed sizes lets you switch quickly between fabric weights. View on Amazon
A quarter-inch quilting presser foot is useful for accurate seam allowances on patchwork blocks. View on Amazon
FAQ
Do I need to rewind the bobbin every time I start a project?
Not always. Rewind when the bobbin runs low or when you change thread color, since a partly used bobbin can shift tension during long seams.
Why does my stitch look different on the back than the front?
This usually points to tension or threading. Rethread the upper path with the presser foot raised, then test again on scrap fabric.
How often should I change the needle?
Change it after roughly eight hours of sewing, or immediately if you hit a pin or notice skipped stitches. A fresh needle often fixes problems that look like tension issues.
Conclusion
With the machine placed correctly, the upper and bobbin threads properly routed, and a test seam checked for balance, you are ready for real work. Match your needle and thread to the fabric, and adjust tension one small step at a time. Keep the bobbin area clean, and your brother computerized sewing and quilting machine xr1355 will stay accurate project after project.
Related reading
Ready to choose one?
